Wireless,Lithium Batteries,Brushless Motor,Magnesium Alloy Trucks (Lead Acid Batteries Available)
Short distance(3m`10m)wireless Control System Without same freguency or radio signal interruption.Our brushless motor allows you to have reverse funtion
Design for two to five years life Cycle.
Home Proudcts Manual & Instruction Comparison * Q & A Warranty Policy Contact Us Distributors Info Price List Video
     Manual & Instruction
Remote controlled Electric Skateboard
OWNERS MANUAL
Introduction to the Remote Controlled Electric Skateboard
Dear customer£º
Congratulations and thank you for purchasing EZskaters. For the greatest pleasure and maximum use of your Electric Skateboard please read this manual thoroughly before your first test ride. With proper use, your EZskaters will provide safe, trouble free service in a long time. Thorough understanding of the information in this manual is the first step in safely enjoying your Electric Skateboard.
 
Preface£º
Your EZskaters is engineered and manufactured with the most technologically
advanced production methods and quality control processes, we inspect and test each Electric
Skateboard before shipment.
Table of Contents
 
Contents                                        
Preface                                             
Important safety information                 
RIDING INSTRUCTIONS                         
Maintaining your ELECTRIC SKATEBOARD  
Parts Diagram of the Electric Skateboard    
1.Inspect outer carton for damages and report any to your freight carrier or dealer.
2.Open carton and inspect for internal damage, report any to your freight carrier or dealer.
3.Remove your new Electric Skateboard, remote controller and charger.
Important Safety information
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO OPERATE YPOUR
ELECTRIC SKATEBOARD
 
 
The combination of power and weight make the ELECTRIC SKATEBOARD a potentially hazardous device.
Improper use can result in property damage, serious injury or even death. Understanding all of its features and
controls is the key to safe riding.
 
Avoid uneven surface, potholes, surface cracks and obstacles. Always ride at a safe speed, maintaining full
control over the board at all times. Adult supervision is strongly recommended.
 
NOT FOR CHILDREN UNDER 14.
¡£
Electric Skateboard SAFETY WARNING
The board does not conform to Motor Vehicle Standards and is not intended for operation on public streets,
roads or highways. Serious injury can result from unsafe operation of this vehicle. The operator can minimize
these assumed risk by wearing safety equipment. Always check your local laws before using in public areas.
 
HELMETS, PROTECTIVE EYEWEAR, APPROPRIATE FOOTWEAR, WRIST, KNEE, AND
ELBOW PROTECTION MUST BE WORN AT ALL TIMES, DO NOT OPERATE THE ELECTRIC
SKATEBOARD IN TRAFFIC ON WET, FORZEN, AND OILY OR UNPAVED SURFACES OR NEAR
PEOPLE OR OTHER VEHICLES.
 
OPERATION WARNING
 
 
¡ó This product is designed for use by children ages 14 and up.
¡ó Electric Skateboard Maximum recommended weight for the rider is 150 Ibs for the EZ-250 model  and 250 Ibs for the rest models, EZ-400, EZ-600 and EZ-800.
¡ó This product should not be used without adult supervision.
¡ó The Electric Skateboard is designed for one rider only.
¡ó Be aware that Strong Electric Magnet Field could interfere the function of the remote controller in your riding area.
¡ó The user of this product and adult supervisor assumes all risks associated with its use. To minimize these assumed risks, the user MUST WEAR SAFETY HELMET, PROTECTIVE EYEWEAR, APPROPRIATE FOOTWEAR, KNEE AND ELBOW PROTECTION AT ALL TIMES.
 
¡ó Do not operate your Electric Skateboard in crowded areas.
 
¡ó NOTE£ºIF YOU DO NOT UNDERSTAND ANY AND ALL PARTS OF THIS SAFETY
OPERATION INFORMATION, PLEASE CALL SKATEBOARD WARRANTY SERVICE
TO CLARIFY ALL POINTS IN THIS OWNER¡¯S MANUAL.
RIDING INSTRUCTIONS
Before riding your new Electric Skateboard, please be sure you fully understand how the model you have purchased operates.
 
IMPORTANT
The Electric Skateboard wireless remote uses a unique 2.4G high frequency radio signal (blue tooth) with distance function of short distance communication and one on one coding function between remote controller and PCB bwhich board which minimizes the possibility of signal interference. Signal interference may occur under strong magnet
Field. Use caution and check your ride area for signal interference before use.
 
Electric Skateboard
 
 
Power Gun Shape Hand Grip Controller 
 
1. The Power Hand Grip Controller regulates the speed of the board. Pulling back on the lever, the board will cause acceleration. Releasing the lever will return it to the neutral position. Pushing forward on the lever wall initiate braking force.
2. After standing on board, pull the power lever. Your Electric Skateboard will start slowly and build speed as you hold the level back.
3. To decrease speed, let the lever go. This will slowly decrease your speed. To slow quicker, push the lever forward to brake. Maximum speed and stopping distance depends on your weight and riding surface.
4. Know your limits. Start slowly and keep your speed down until you have mastered controlling your ELECTRIC SKATEBOARD.
5. Read the section titled: ¡°Riding your Electric Skateboard before attempting to ride¡±.
Power Oval Shape Hand Grip Controller
 
                        
1.Hold the oval remote controller as the Picture above shows. The thumb is for braking function, the first finger is for acceleration, the middle finger is for deceleration, the ring finger is for reverse function.
2.Turn on the switches on both the remote controller and the power board, matching one on one coding by using any needle shape pin to push the coding point beside the red light, you can make sure the remote controller and the PCB board are coding with each other by looking at the green light keep flashing on side of PCB board box. Standing on board and tapping the first finger button for acceleration, there are more than 10 shift speeds function in the riding system, you can accelerate the speeds separately from shift to shift when you quickly tap the first finger button separately, but the speed shift can go all the way to its maximum when you hold the first finger button for more than one second.
3.The middle finger button is for deceleration, there are more than 10 shift deceleration function in the riding system, you can decelerate the speeds separately from shift to shift when you quickly tap the middle finger button separately, and the acceleration can go from the speed you are riding all the way to the neutral when you hold the middle finger for more than one second.
4.The thumb button is for brake function, any moment the board will brake when you tap or hold the brake button, be ware of always giving yourself some buffering time and distance by slowing down before tapping or holding the brake button.
5.Reverse button is for reverse function when you want to ride backward or reverse direction. Reverse button works only after you tap the brake button or when you are in the first tap shift speed, the first finger button and the middle finger button work the same way for the reverse riding direction.
6.Maximum speed and stopping distance depends upon your weight and riding surface, know your own limits, start slowly and keep your speed down until you have mastered controlling your EZskaters.
7.Read the section titled: ¡° Riding your Electric Skateboard before attempting to ride.¡± 
 
 
THROTTLE/BRAKE SAFETY WARING
   The Electric Skateboard is a powerful device, if you step on and pull the power lever or tap the acceleration
, button, you could be
THROWN BACKWARD FROM THE BOARD. If traveling at high speed, pushing the lever forward
quickly £¨engaging the brake£©or hold the deceleration button or tap the brake button could
THROW YOU FORWARD FROM THE BOARD. KNOW YOURLIMITS AND USE THE
POWER HAND GRIP CONTROLLER OR HANDLE THE BUTTONS OF THE OVAL SHAPE
CONTROLLERS  ACCORDINGLY.  THERE IS A MOMENTARY TIME LAG FOR POWER AND
BRAKE ACTIVATION.
 
 
Hand Controller Battery
 
 
The hand controller uses a standard 9-volt alkaline battery. Switching the controller off when not in use will maximize battery life. If you notice unreliable communication with the board, the battery should be replaced.
Power Switch
The Electric Skateboard is equipped with an ¡°ON OFF¡± switch on the side of the battery box on your board. To
start the Electric Skateboard, turn the switch to the ¡°ON¡± position. Make sure to turn the board to the ¡°OFF¡± position when not in use. Leaving the switch in the ¡°ON¡± position when not in use may damage the electronics and battery.
 
 
Adjustments
Under normal use the Electric Skateboard requires no adjustments. However, it is prudent to check all fasteners for tightness before every use. The brushings in the trucks are specially formulated to provide stock absorption and positive steering control for the Electric Skateboard.
RIDING YOUR ELECTRIC SKATEBOARD
BEFORE YOUR RIDE
Be sure that you are thoroughly familiar with all of the features and controls discussed in the previous section.
All safety equipments should be worn, even when riding for short distances or durations. Make sure that the area in which you plan to ride is paved, level, free of obstacles, and not crowded.
 
SAFETY WARNING
  You are about to climb aboard a powerful motorized skateboard. If you have doubts about your ability to
  ride, DO NOT RIDE IT£¡Know your limits and ride within them. Even if you are an expert skateboarder,
  give yourself time to learn the Electric Skateboard and ride conservatively, especially the first few times.
  Remember, the Electric Skateboard is silent used others will not hear you coming. Give yourself adequate time
 and distance to stop and avoid obstacles and others.
 
 
 
GETTING STARTED
Make sure the switch to the ELECTRIC SKATEBOARD is ¡°ON¡± and the switch on the hand controller is
¡°OFF¡±. Step on to the skateboard and assume a normal skateboard stance£¨training forward, knees slightly
Bent.£©Keeping your fingers off the power lever, turn the switch on the top of the controller to the ¡°ON¡± position.
Pull the lever or tap the first finger button for a moment to start the board. Start off slowly by pulling the lever back or remaining in the first tap speed until you become comfortable and in control of the speed.
Uphill and Downhill Riding
The ELECTRIC SKATEBOARD is far superior to an ordinary skateboard in uphill and downhill riding. On and uphill run, you will find that you need in keep your weight over the rear wheels to keep them from slipping. If the hill is too steep, the board will bog down and continued use may overheat the motor. Stop, step off and walk the steep hills. This board will take lighter weight riders up hills faster and will slow down as the rider¡¯s weight increases. Take advantage of the reverse function and make the driving wheel in front when you are riding uphill, the power board run more efficient uphill when the driving wheel is in the front.
 
On downhill runs, the motor remains engaged at all times. Providing same drag or button to slow. You also have hill breaking control. Frequent minor speed corrections with the brakes are preferable to not letting your speed build up and then braking suddenly.   KNOW YOUR LIMITS AND RIDE WITHIN THEM£¡
 
 
 
 
SPEED
NEVER RIDE DOWN HILLS THAT ARE TOO STEEP.TO MAINTAIN SAFE OF YOUR ELECTRIC
SKATEBOARD NEVER RIDE DOWN HILLS THAT REQUIRE CONSTANT BREAKING,
AS IT CAN DAMAGE THE BOARD¡¯S ELECTRONICS.
 
Turning your Electric Skateboard
The Electric Skateboard turns like any other skateboard. Apply pressure to the deck with your heels or toes
and the board will turn in that direction. Make pressure will result in tighter turns. In the hands of experienced
rider, the ELECTRIC SKATEBOARD is capable of making 10¡±radius 180o turns.
Do not try to make turns at full speed. Always SLOW DOWN£¡
MAINTAINING YOUR ELECTRIC SKATEBOARD
MAITENANCE WARNING
FAILURE TO FOLLOW MIANTENANCE INSTRUCTIONS AND GUIDELINES WILL VOID YOUR
WARRANTY. DO NOT OPEN BATTERY BOX£¡DOING SO WILL VOID YOUR WARRANTY.
 
Routine Maintenance
Under normal use, your ELECTRIC SKATEBOARD will require very little maintenance. Check all fasters
for tightness before every use, especially if used on irregular surface. This will require an Allen wrench and a few different sized sockets or open-ended wrenches. Your ELECTRIC SKATEBOARD is not waterproof
and must not be ridden in the rain, mud, or other wet areas to prevent electrical damage. Always keep your board clean and free of moisture.
 
 
Drive Wheel Replacement
It is normal for the drive wheel to wear faster than the other wheels. DRIVE WHEEL REPLACEMENT are available from Manufacturer or Dealers.
 
 
Drive Belt Replacement
Due to the superior design of the Electric Skateboard the drive belt will last a long time, but eventually will wear out. Replacements can be ordered from Manufacturer or Dealers.
Wheel Replacement
As with any skateboard, the wheels of the ELECTRIC SKATEBOARD will wear out with use.
Replacement wheels, bearing, and spacers are available from Manufacturer or Dealers.
 
Rubber Bushing Replacement
Although specially formulated for extremely long life, the rubber bushings located in the trucks of your
ELECTRIC SKATEBOARD will wear over time. It is recommended that be replaced with the same special bushings that are standard equipment on the board. They are available through Manufacturer or Dealers.
 
Battery Maintenance
 
The rechargeable Lead Acid battery that powers your Electric Skateboard should last 1-2 years if kept properly
charged, but will slowly decrease in capacity and eventually fail to hold a charge. To maintain maximum life always keep your Electric Skateboard charged when storing for extended periods of time. Plug in once a month to maintain a charge. They are easily replaceable using without any Replacement Kit, Lead Acid battery is a available from Manufacturer or Dealers. See diagram below. The rechargeable Lithium battery that powers your Electric Skateboard should last 2-5 years if kept properly charged, and it will not slowly decrease in capacity or eventually fail to hold a charge, but it will decrease 10% to 20% in capacity after more than 500 times charge. To maintain maximum life always keep your Electric Skateboard charged when storing for extended periods of time. Plug in once in three months to maintain a charge when you are not riding your power board. They are easily replaceable without any Replacement Kit, Lithium battery is a available from Manufacturer or Dealers. See diagram below. ALWAYS STORE YOUR ELECTRIC SKATEBOARD
ON THE WHEELS LEVEL NOT STANDING ON END.
Repair Information
Many repairs that may be required for your Electric Skateboard are covered in the maintenance section of this guide. Should your Electric Skateboard require repairs that are not covered under this section, contact Manufacturer or Dealer with the nature of the problem of Electric Skateboard.
For more information on how to obtain technical support or an authorized service center location contact
EZskaters Manufacturer or Dealer.
Manufacturer warranties your ELECTRIC SKATEBOARD for 30 days from the date of original purchase against manufacturer¡¯s defects in materials and workmanship. The warranty DOES NOT COVER
MALFUNCTIONS RESULTING FROM NEGLECT, MISUSE, ABUSE, and MODIFICATIONS
TO THE BOARD OR FAILURE TO FOLLOW ALL SAFETY AND USE WARNINGS CONTAINDED
HEREIN.
 
Warranty in limited to the EZSKATERS¡¯ ELECTRIC SKATEBOARD    Manufacturer assumes NO LIABILITY for any other components.
© 2008 - 2016 - CopyRight The Most Advanced New Generation Powerboard all right reserved